Hanna-instruments HI 504 Instrukcja Użytkownika Pobierz pdf (Strona 14)

2726

Note While in the setup mode, if no activity is performed for about

5 minutes after entering the setup mode, the mode is auto-

matically exited and the instrument returns to the previous

mode.

The below table lists the setup codes along with the description of

the specific setup items, their valid values and whether the item is

present for ORP mode.

Titles in Italic character (e.g.. “SETPOINT 1 “) represent different

su/jointfilesconvert/1702243/bgroups within the same group. The su/jointfilesconvert/1702243/bgroup name (e.g..

“Set1”) is showed when entering the first item of the sub-

group. To scroll through su/jointfilesconvert/1702243/bgroups, use the  key.

Depending on the device model, some of the below items or

item values may not be available.

Code Valid Values Default Present

for ORP

GENERAL (“GEnE”)

G.00 pH/ORP input “PH”, “OrP” (see note 10) “PH” yes

G.01 Temperature compensation “AtC”: Automatic “AtC” no

“USEr”: Manual (see notes 9, 25)

G.02 Manual or probe error -30 to 130.0 ºC 25.0 no

temperature (see notes 9, 25)

G.10 Factory ID 0000 to 9999 (see note 20) 0000 yes

G.11 Process ID alias RS485 address 00 to 99 (see note 20) 00 yes

G.12 Hardware Identifier 7 digits identification number, read only yes

(see notes 4, 20)

G.98 Calibration/hold password 0000 to 9999 (see notes 2, 20) 0000 yes

G.99 General password 0000 to 9999 (see notes 2, 20) 0000 yes

CONTROL (“CtrL”)

C.00 Control enable “OFF”: Control mode disabled “OFF” yes

“On”: Control mode enabled

SETPOINT 1 (“SEt1”)

C.10 Setpoint 1 mode (M1) “OFF”: Disabled “OOHI” yes

(see note 1) “OOHI”: ON-OFF, high set point

“OOLO”: ON-OFF, low set point

“PIdH”: P.I.D., high set point / “PIdL”: P.I.D., low set point

C.11 Setpoint 1 (S1) -2.00 to 16.00 pH or 8.00 pH or yes

(see note 1) -2000 to 2000 mV 500 mV

Otherwise, if a numeric value has to be entered for the

item, use the æ or  key to change the value of the blink-

ing digit and the  key to cycle through the number’s

digits.

• Once a value is set, press the CFM key to confirm. The

instrument will turn to the next item and the new item’s

value will be displayed on the primary LCD.

• If a wrong value is confirmed, the

WRONG indicator starts blinking,

the new value is not accepted and

the instrument will not switch to the

next item until a correct value will

be confirmed.

• Instead of selecting the item manually, it is possible to cycle

through all the items of a selected group by pressing re-

peatedly CFM key. The procedure to modify the item’s value

is the same described above.

If the last item of the group is reached, by pressing the

CFM key again the primary display will show the group

name and it will be possible to change the group by press-

ing the æ or  key.

Note At any time for exiting the setup mode press the SETUP key. If

no modification has been confirmed, no setup item is

changed.

1 2 ... 9 10 11 12 13 14 15 16 17 18 19 ... 58 59

Komentarze do niniejszej Instrukcji

Brak uwag

Hanna-instruments HI 504 Instrukcja Użytkownika Strona 14

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Urządzenia pomiarowe Hanna-instruments HI 504